Ribbon and flat cable assemblies, quoted in 24 hours.
Pitch, ways, orientation and the position of every connector on the run. Send the drawing or the part numbers off the assembly you are replacing, and a fixed price comes back — IDC or crimped, single or daisy-chained.
All uploads are secure & protected by NDA.
24 h
Quote turnaround on a complete spec
10 days
Production lead times from 10 days
50+
Carefully vetted manufacturing sites across the globe
IPC-620
Certificates available on request
Three steps from drawing to delivery.
You upload a spec and approve a price. We'll take care of the rest.
Upload your spec & get a quote
A drawing, BOM, wire schedule, EPLAN export — a photo of the harness you're replacing, or just a description of the build. A fixed price comes back within 24 hours.
Review & confirm your quote
We make it production-ready before anything is built: connectors, wire gauges, strip lengths and tolerances normalised into a manufacturable spec, with anything missing flagged to you.
Built & delivered
Production from 10 days, 100% continuity-tested, with test records and IPC-620 certificates on request. We ship worldwide, including Europe, the UK, the USA, Australia and Southeast Asia.
Quote a ribbon or IDC assembly in 24 hours.
Pitch, way count, overall length and where each connector sits. A photo of the assembly you are replacing, with the connector part numbers legible, is enough to start.
- Uploads are encrypted and NDA-protected
- If anything's missing, we'll ask — not guess
- Once you approve, we'll place your order with a vetted manufacturer from our network
What our customers say
Everything went as expected, much appreciated. We will keep using your wire harness services in the future.
Capacity where your order needs it.
Every order goes to the partner best placed to build it — chosen for the processes your drawing needs, the certification it has to carry, and the lead time you are working to. Every manufacturing partner was carefully vetted before taking on work.
Region is a filter on an order, not a fixed answer. If your project has to be built in a particular country or economic area, say so on the enquiry and we will confirm at quote time whether we can place it there.
Where our ribbon assemblies go to work.
Every sector below has its own qualification requirements. We match your project to a manufacturer that already builds to them.
Vehicles & off-highway
Cab, chassis and engine harnesses, sealed and vibration-rated for trucks and off-highway machines.
OEM & electronics
Board-to-board looms, IDC ribbon, FFC and internal interconnects for electronic products.
Medical & life science
Biocompatible materials, full traceability and controlled-change production.
Robotics & automation
High-flex drag-chain and torsion cable, servo, encoder and teach-pendant assemblies.
Industrial machinery
Control-cabinet looms, sensor and actuator harnesses, IP67 connector systems.
RF & telecom
RF and power assemblies, backplane test cables, PSU and control harnesses.
Energy & power
Busbar links, battery-module and fuel-cell interconnects, inverter and BMS looms.
HVAC & building systems
Sensor and thermistor leads, mains inlets and control harnesses for HVAC equipment.
Railroad
EN 45545 fire-rated, halogen-free materials and vibration-resistant terminations.
Every pitch, termination and test we can quote.
Capabilities across our partner network for flat cable. Your project is matched to a manufacturer already tooled for the pitch and the way count it needs.
Assembly
- 1.27 / 2.00 / 2.54 mm pitch, grey and coloured-stripe ribbon
- The standard way counts — 10, 14, 20, 26, 34, 40, 50 and the rest
- IDC mass termination, or contact-by-contact crimping where the drawing calls for it
- Daisy-chained and bridged runs, connectors placed to your dimensions
- Twisted-pair ribbon — bonded pairs along the run, flat at the terminations
- Cable folding, strain-relief bars and polarising keys fitted
Components
- IDC sockets, box headers, card-edge and DIP ends
- 3M, Amphenol, TE / AMP, Molex and Harting flat-cable families
- Grey, rainbow and coloured-stripe ribbon to the specification your drawing names
- Shielded and unshielded ribbon, 28 AWG stranded or solid conductors
- Obsolescence checks and drop-in alternates at quote time
Test & documentation
- 100% continuity testing against your pin-out, way by way
- Pin-one orientation checked against the drawing
- Hipot and insulation-resistance testing where specified
- Lot traceability on cable and connectors
- First-article inspection reports and certificates on request
IPC/WHMA-A-620 is the industry standard for cable and wire harness assemblies. Certificates for your assigned manufacturer are available on request.
Questions engineers & buyers ask.
1.27, 2.00 and 2.54 mm are everyday work and are quoted without qualification. Anything else, send the drawing and we confirm at quote time whether the network is tooled for it.
IDC terminates every conductor at once through the insulation, and on a standard pitch it is the normal choice. Crimped contacts are used where the drawing calls for a connector with no IDC version, where conductors have to be split out of the ribbon, or where a higher retention force is specified. Say which the drawing specifies; if it doesn't, we'll ask.
Yes. Daisy-chained runs with intermediate connectors are standard work. Give us the dimension from datum to each connector and the orientation of each, and they are placed to the drawing.
Yes — ribbon with bonded twisted sections along the run and flat sections at the termination points. It is specified by the twisted length and the flat length; the cable's part number is usually enough for us to price it.
The standard counts across the common range are everyday work. An unusual count is a question of what the connector is available in rather than what the shop can do, so send the connector part number with the enquiry.
Orientation is checked against the drawing, and continuity is tested against your pin-out — not a generic one — so a mirrored connector fails the test before it leaves the building.
Ready to quote your ribbon assemblies?
- Quote
- 24 h
- Production
- 10 days
- Minimum
- None